| Production
Speed: |
 1-45
loads per hour
NOTE: Process rates will vary with load size,
number of wraps & conveyor speed |
 |
| Load Capacity: |
Maximum
load weight: 4,000# dynamic – 12,000#
static
Maximum load size: 50” W x 50” L
x 82” H (71” max. load
diagonal)
Minimum load size: 30” W x 30” L
x 24” H |
|
| Turntable: |
80” diameter
skirted turntable
4000# dynamic weight capacity
29” diameter ring gear support
system, direct pinion-to-
gear drive
1-15 RPM rotational speed c/w soft
start acceleration and
positive stop alignment
1 HP DC drive motor c/w turntable
holding brake
Remote centralized lubrication for
ring gear |
|
| Film Carriage Elevator: |
1/2
HP DC variable speed motor
ANSI #40 direct chain drive c/w shock
dampener
Maintenance free 12 point carriage
guidance system |
|
| Film Delivery System: |
Rapid
Thread™ 20” capacity pre-stretch
film carriage
1/2 HP DC variable speed motor
Fully electronic dynamic dancer corner
compensation
33 to 313% fixed stretch capability
(shipped fixed at
250%)
Pre-stretch ratio variable by easy
sprocket change
Rapid Thread™ (Safety Door) with auto
power cut-off
switch |
|
| Powered Roller Conveyor: |
Basic system: 5ft Infeed section,
80” diameter
turntable section & 5ft Exit section
Each section includes:
Chain driven live roller conveyors
Rated 4,000# per section
2-1/2” diameter 11 gauge rollers
c/w 11/16” hex axles on
3” centers
All rollers ANSI # 40 chain driven,
roller to roller
54” effective roller width
Conveyor speeds 20 to 50 FPM (specify
required speed)
with electronic soft start
Pass-line height – 18” from
floor to top of rollers
1/2 HP AC variable speed reversible
TEFC motor
(turntable conveyor is 1/2 HP
DC)
Automatic load indexing and centering
by photo-eye &
PLC logic |
|
| Control Features: |
PANASONIC FP-X Programmable Logic Controller (PLC)
HMI Touchscreen Operator Interface
Panel
Illuminated power start/reset button
Emergency stop mushroom button
Wrap cycle start (rewrap) button
Manual controls provided for turntable
jog, film carriage
elevator lower/raise,
film
clamp open/close and conveyors
forward/reverse
Separate film carriage elevator raise & lower
speed
controls
Film tension (force-to-load) control
Separate top & bottom wrap counters
Auto load height detection photo-eye
Broken film/out of film detection
c/w automatic machine
reset and fault beacon
light
Turntable drive and film carriage
elevator dynamic braking
systems
Wrap bypass mode
NEMA 12 control panel and junction
boxes
Dust tight slip ring assembly
Non-proprietary UL/CSA approved components |
|
| Automation Features: |
Pneumatically
actuated film clamp mechanism
Pneumatically actuated film tail cut/wiper
arm
mechanism
Ni-chrome impulse hot wire film cut
off c/w automatic
periodic cleaning cycle |
|
Structural Features:
|
All
structural steel construction
Forklift truck portable base structure
design
Structural steel H-beam machine tower
Electro-static powder coated paint
finish |
|
| Safety Features: |
Safety
barriers enclose the turntable section to
prevent
personnel intrusion
Operator access gate c/w safety switch
disables
operation when gate is opened |
|
| Electrical Requirement: |
208Y/120
Volts 3 Phase 60 Hz 30 Amps |
|
| Pneumatic Requirement: |
3
CFM @ 80 PSI clean dry pneumatic supply required
Filter/regulator c/w gauge & lock-out
valve provided |
|
| Typical System Dimensions: |
202” (L)
x 143” (W) x 100” (H)
(Standard dimensions are approximate) |
