| Production
Speed: |
 1-95
loads per hour
NOTE: Process rates will vary with load size,
number of wraps & conveyor speed |
 |
| Load Capacity: |
Maximum
load weight: 4000# dynamic – 12,000#
static
Maximum load size: 50” W x 60” L
x 80” H (79” Max. load
diagonal)
Minimum load size: 30” W x 30” L
x 24” H |
|
| Rotary Arm: |
20” diameter
ring bearing support system
ANSI #80 direct chain drive c/w chain
tensioner
1-33 RPM rotational speed c/w soft
start acceleration and
positive stop alignment
3 HP DC rotary arm drive motor
Air-operated rotary arm braking system
Central lube system |
|
| Film Carriage Elevator: |
1
HP DC variable speed motor
Electrically-operated fail-safe brake
ANSI # 50 direct chain drive c/w shock
dampeners
Maintenance free 18 point carriage
guidance system |
|
| Film Delivery System: |
Rapid
Thread™ 20”/30” capacity
pre-stretch film carriage
1 HP DC variable speed motor
Fully electronic dynamic dancer corner
compensation
33 to 313% fixed stretch capability
(shipped fixed at
250%)
Pre-stretch ratio variable by easy
sprocket change
Rapid Thread™ (Safety Door) with auto
power cut-off
switch |
|
| Powered Roller Conveyor: |
Basic system: 5 ft. infeed section, 12
ft. Process/wrap zone section and 5 ft. exit
section
Each
section
includes:
Chain
driven
live
roller
conveyors
Rated
4,000#
per section
2-1/2” diameter
11 gauge
rollers
c/w 11/16” hex
axles
on
3” centers
All
rollers
ANSI
# 40
chain
driven,
roller
to roller
54” effective
roller
width
Conveyor
speeds
40 to
70 FPM
(specify
required
speed)
with
electronic
soft
start
Pass-line
height – 18” from
floor
to top
of rollers
1
HP AC
variable
speed
reversible
TEFC
motor
Automatic
load
indexing
and centering
by photo-eye &
PLC
logic |
|
| Control Features: |
Allen-Bradley SLC-5/03 Programmable Logic Controller
Allen-Bradley PanelView 600 Color Operator
Interface
c/w Keypad and Touch Screen provides
diagnostic
messaging and machine status
information
Illuminated power start/reset button
Emergency stop mushroom button
Wrap cycle start (rewrap) button
Manual controls provided for rotary
arm jog, film carriage
elevator lower/raise,
Film clamp open/close and conveyors
forward/reverse
Separate film carriage elevator raise & lower
speed
controls
Film tension (force-to-load) control
Separate top & bottom wrap counters
Auto load height detection photo-eye
Broken film/out of film detection
c/w automatic machine
reset and fault beacon
light
Rotary arm and film carriage elevator
dynamic braking
system
Wrap bypass mode
NEMA 12 control panel and junction
boxes
Dust tight slip ring assembly
Non-proprietary UL/CSA approved components |
|
| Automation Features: |
Pneumatically
actuated film clamp mechanism
Pneumatically actuated film tail cut/wiper
arm
mechanism
Ni-chrome impulse hot wire film cut
off c/w automatic
periodic cleaning cycle |
|
Structural Features:
|
All
structural steel construction
Structural tube machine tower & frame
Electro-static powder coated paint
finish |
|
| Safety Features: |
Personnel
safety – rotary arm obstruction emergency
stop sensor
Safety barriers enclose the wrap zone
to prevent
personnel intrusion
Operator access gate c/w safety switch
disables
automatic operation when gate is
opened |
|
| Electrical Requirement: |
460
Volts 3 Phase 60 Hz 30 Amps |
|
| Pneumatic Requirement: |
3
CFM @ 80 PSI clean dry pneumatic supply required
Filter/regulator c/w gauge & lock-out
valve provided |
|
| Typical System Dimensions: |
264” (L)
x 170” (W) x 156” (H)
Overall includes conveyor (L) and Control
panel (W) – all dimensions approximate |
