| Production
Speed: |
 1-35
loads per hour
NOTE: Process rates will vary with load size,
number of wraps & forklift load/unload
time |
 |
| Load Capacity: |
Maximum
load weight: 4,000# dynamic – 12,000#
static
Maximum load size: 48” W x 48” L
(68” max. load
diagonal) x 80” H
(+ up to 4” top overlap) |
|
| Turntable: |
72” diameter
3/8” thick laser-cut steel plate with
5” skirt
Front and side cut-outs with UHMW
flexible contouring for
fork truck access
6-point heavy duty taper-roller bearing
caster support
system
ANSI # 60 direct chain drive c/w chain
tensioner
3-16 RPM rotational speed c/w soft
start acceleration
3/4 HP DC variable speed drive motor
c/w turntable
holding brake
Final revolution deceleration and
positive stop alignment |
|
| Film Carriage Elevator: |
1/2
HP DC variable speed motor
Flat Belt & Pulley with Carriage
Anti-Fall Device
Maintenance free 12 point carriage
guidance system |
|
| Film Delivery System: |
Rapid
Thread™ 20” capacity pre-stretch
film carriage
1/2 HP DC variable speed motor
Fully electronic dynamic dancer corner
compensation
33 to 313% fixed stretch capability
Pre-stretch ratio variable by easy
sprocket change
Rapid Thread™ (Safety Door) with auto
power cut-off
switch
Carriage descent obstruction shut-off
device for additional
safety
Side mounted film carriage for operator
convenience and
safety |
|
| Powered Roller Conveyor: |
Basic system: 72” dia. powered Process/Turntable
section & 5 ft. Gravity Outfeed section
Turntable
section includes:
Chain
driven live roller type conveyor
Rated 4,000# per section
2-1/2” diameter 11 gauge rollers
c/w 11/16” hex axles on
3” centers
All rollers ANSI # 40 chain driven,
roller to roller
50” effective roller width
Conveyor speed variable up to 28 FPM
with electronic
soft start
Pass-line height – 16-1/2” from
floor to top of rollers
1/2 HP DC variable speed motor |
|
| Control Features: |
PANASONIC PLC with Touchscreen Operator Interface
Power Off – On – Reset
Switch & Power
On Indicator
Light
Cycle Pause for applying top sheets
Reinforce wrap control for mid-wrapping
Emergency Stop Button
Turntable Jog Button
Film Carriage Lower/Raise Buttons
Eject Load (Turntable Conveyor Jog)
Button
Film Tension (Force-to-Load) Control
Selectable Reduced Film Tension parameters
for
wrapping top and/or bottom of load
Separate Film Carriage Raise & Lower
Speed controls
Variable Turntable Speed Control
Triple Beam Automatic Load Height Detection
sensor for
dark or shiny loads
Separate 1 to 12 Revolution Top & Bottom
wrap control
Gravity conveyor full photo-eye
Broken film/out of film detection c/w
automatic machine
reset
Stack-light beacon indicates run, clear
or fault
Remote pendant start switch
NEMA 12 control panel enclosure
Non-proprietary UL/CSA approved components |
|
| Automation Features: |
“All
Electric – No Pneumatics Required”
“Patent Pending” Cousins exclusive
patent pending
A-Arm cut and clamp device
starts and ends the wrap process at the top
of the load. This uniquely different approach
to attaching and cutting the stretch film
provides you with these benefits:
Selectable
top banding capability
Stabilizes the load early in the wrap cycle
Places the ending film tail at the top
of the load instead of
the bottom
Eliminates the need of a film clamp power
source on the
turntable for easier maintenance
No air hook-ups or noisy compressors
Load placement on the turntable is not
critical
There is no film clamp on the turntable
that can be
damaged by debris or operator
error
|
|
Structural Features:
|
All
structural steel construction
Forklift truck portable base structure
design – lifting
tubes
included for front and rear access
Structural steel tube machine tower
c/w sheet metal
covers
Electro-static powder coated paint
finish |
|
| Electrical Requirement: |
115
Volts 1 Phase 60 Hz 20 Amps |
