| Production
Speed: |
 1-40
loads per hour
NOTE: Process rates will vary with load size,
number of wraps & forklift load/unload
time |
 |
| Load Capacity: |
Maximum
load weight: 4,000# dynamic – 12,000#
static
Maximum load size: 48” W x 48” L
(68” max. load
diagonal) x 80” H
(+ up to 4” top overlap) |
|
| Turntable: |
72” diameter
3/8” thick laser-cut steel plate with
5” skirt
Front and side cut-outs with UHMW
flexible contouring for
fork truck access
6-point heavy duty taper-roller bearing
caster support
system
ANSI # 60 direct chain drive c/w chain
tensioner
3-16 RPM rotational speed c/w soft
start acceleration
3/4 HP DC variable speed drive motor
c/w turntable
holding brake
Final revolution deceleration and
positive stop alignment |
|
| Film Carriage Elevator: |
1/2
HP DC variable speed motor
Flat Belt & Pulley with Carriage
Anti-Fall Device
Maintenance free 12 point carriage
guidance system |
|
| Film Delivery System: |
Rapid
Thread™ 20” capacity pre-stretch
film carriage
1/2 HP DC variable speed motor
Fully electronic dynamic dancer corner
compensation
33 to 313% fixed stretch capability
Pre-stretch ratio variable by easy
sprocket change
Rapid Thread™ (Safety Door) with auto
power cut-off
switch
Carriage descent obstruction shut-off
device for additional
safety
Side mounted film carriage for operator
convenience and
safety
|
|
| Powered Roller Conveyor: |
Basic system: 72” dia. powered Process/Turntable
section & 5 ft. Gravity Outfeed section
Turntable section includes:
Chain driven live roller type conveyor
Rated 4,000# per section
2-1/2” diameter 11 gauge rollers
c/w 11/16” hex axles on
3” centers
All rollers ANSI # 40 chain driven,
roller to roller
50” effective roller width
Conveyor speed variable up to 28 FPM
with electronic
soft start
Pass-line height – 16-1/2” from
floor to top of rollers
1/2 HP DC variable speed motor X |
|
| Control Features: |
PANASONIC PLC with Touchscreen Operator Interface
Power Off – On – Reset
Switch & Power
On Indicator
Light
Cycle Pause for applying top sheets
Reinforce wrap control for mid-wrapping
Emergency Stop Button
Turntable Jog Button
Film Carriage Lower/Raise Buttons
Film Clamp Open/Close Button
Eject Load (Turntable Conveyor Jog)
Button
Film Tension (Force-to-Load) Control
Selectable Reduced Film Tension parameters
for
wrapping top and/or bottom of load
Separate Film Carriage Raise & Lower
Speed controls
Variable Turntable Speed Control
Triple Beam Automatic Load Height Detection
sensor for
dark or shiny loads
Separate 1 to 12 Revolution Top & Bottom
wrap control
Gravity conveyor full photo-eye
Broken film/out of film detection c/w
automatic machine
reset
Stack-light beacon indicates run, clear
or fault
Remote pendant start switch
NEMA 12 control panel enclosure
Non-proprietary UL/CSA approved components |
|
| Automation Features: |
“All Electric – No
Pneumatics Required”
Electro-mechanically actuated film
clamp mechanism
Electro-mechanically actuated film
tail cut/wiper arm
mechanism
Ni-chrome impulse hot wire film cut
off c/w automatic
periodic cleaning cycle |
|
Structural Features:
|
All
structural steel construction
Forklift truck portable base structure
design – lifting
tubes
included for front and rear access
Structural steel tube machine tower
c/w sheet metal
covers
Electro-static powder coated paint
finish |
|
| Electrical Requirement: |
115
Volts 1 Phase 60 Hz 20 Amps |
